Troubleshooting a microwave oven will be tough, however some of the widespread issues is a defective magnetron. The magnetron is the part that generates the microwaves that cook dinner your meals, so if it isn’t working correctly, your microwave will not be capable to warmth meals successfully. There are some things you are able to do to test in case your microwave magnetron is working correctly, and we’ll stroll you thru them on this article.
First, you may want to collect a couple of instruments. You will want a multimeter, a screwdriver, and a pair of pliers. After getting your instruments, you can begin the troubleshooting course of. First, unplug your microwave from the wall outlet. Then, take away the again panel of the microwave. Watch out to not contact any of {the electrical} parts contained in the microwave. After getting the again panel off, you can see the magnetron. The magnetron is a big, cylindrical part with a steel cap on one finish.
Subsequent, you may have to test the continuity of the magnetron. To do that, set your multimeter to the ohms setting. Then, contact one probe of the multimeter to the steel cap of the magnetron and the opposite probe to the physique of the magnetron. If the multimeter reads 0 ohms, then the magnetron is working correctly. If the multimeter reads infinity, then the magnetron is defective and can should be changed. Should you’ve checked the continuity of the magnetron and it is working correctly, then the issue could also be with one other part within the microwave. You possibly can attempt changing the capacitor or the diode, but when that does not repair the issue, you then’ll have to name a professional equipment restore technician.
Determine the Magnetron Location
The magnetron is a essential part of a microwave oven, producing the electromagnetic vitality that heats meals. To entry the magnetron, observe these detailed steps:
Find the Entry Panel
Usually, microwave ovens have a detachable entry panel situated both on the high, rear, or backside of the oven. Seek the advice of your equipment guide or search on-line to your particular mannequin to find out the placement of this panel.
Unplug the Oven
For security causes, unplug the microwave oven from {the electrical} outlet earlier than making an attempt any repairs. Permit the capacitors to discharge by ready a number of minutes earlier than continuing.
Take away the Entry Panel
Utilizing a Phillips head screwdriver, take away the screws securing the entry panel to the oven. As soon as the screws are eliminated, rigorously elevate the entry panel away from the microwave and set it apart.
Find the Magnetron
As soon as the entry panel is eliminated, you should have entry to the interior parts of the microwave oven. The magnetron is often situated on the backside of the oven cavity, in the direction of the again. It’s a cylindrical-shaped part with a big cap on one finish and several other steel fins radiating from its sides.
Security Precautions
1. Unplug the Microwave
- Earlier than starting any repairs or inspections, all the time disconnect the microwave from the ability supply.
2. Discharge the Excessive-Voltage Capacitor
-
The magnetron capacitor shops excessive voltage, making it harmful to deal with. To soundly discharge the capacitor:
-
- Use a Excessive-Voltage Probe: Join a high-voltage probe or an insulated screwdriver to the capacitor’s unfavorable terminal and floor it securely.
-
- Bleed the Capacitor with a Resistor: Connect a high-value resistor (10kΩ or greater) throughout the capacitor terminals. Look ahead to a couple of minutes to permit the capacitor to discharge.
-
- Put on Insulated Gloves: Make sure the gloves are rated for top voltage (1000V or greater).
Warning:** By no means contact the HV terminal or part instantly.
3. Deal with the Magnetron with Care
- The magnetron is a fragile part and needs to be dealt with with care to keep away from harm. Use insulated instruments, and by no means power connections.
- Use a correct socket wrench to tighten the mounting bolts. Keep away from overtightening, as this will warp or harm the magnetron.
Making ready the Microwave
Earlier than performing any diagnostic assessments, it is essential to make sure the protection of each your self and the microwave oven. Comply with these steps rigorously:
1. Unplug the Microwave
Find the ability twine related to {the electrical} outlet and unplug it fully.
2. Discharge the Capacitor
Contained in the microwave oven, there is a high-voltage capacitor that should be discharged earlier than dealing with any electrical parts. To do that, use a non-conductive instrument like a plastic screwdriver to brief the terminals collectively. Hold one finish of the screwdriver on every terminal whereas carrying insulated gloves.
3. Take away the Outer Case
The outer case of the microwave usually consists of a steel body and plastic panels. Rigorously take away the screws holding the outer case in place and gently elevate it off. Be affected person and keep away from making use of extreme power that would harm the casing or its parts.
| Screw Location | Amount |
|---|---|
| Prime Panel | 4 |
| Facet Panels | 2 either side |
| Backside Panel | 4 |
Finding the Magnetron
The magnetron is often situated on the high of the microwave, behind the waveguide cowl. To entry the magnetron, you will have to take away the outer casing of the microwave. After getting eliminated the outer casing, you will note the waveguide cowl. The waveguide cowl is often held in place by a couple of screws. Take away the screws and elevate off the waveguide cowl to show the magnetron.
The magnetron is a cylindrical-shaped part with a high-voltage capacitor connected to it. The capacitor is often coated by a plastic or rubber boot. To check the magnetron, you will have to take away the capacitor boot and join a multimeter to the terminals of the capacitor.
Checking the Magnetron Resistance
To test the resistance of the magnetron, set your multimeter to the ohms setting. Join the optimistic lead of the multimeter to at least one terminal of the capacitor and the unfavorable lead of the multimeter to the opposite terminal of the capacitor. The resistance of the magnetron needs to be between 0.2 and 0.5 ohms. If the resistance will not be inside this vary, the magnetron is defective and can should be changed.
| Magnetron Resistance | Standing |
|---|---|
| 0.2 – 0.5 ohms | Good |
| Lower than 0.2 ohms | Quick circuit |
| Better than 0.5 ohms | Open circuit |
Visible Inspection
Checking the magnetron visually is a fast and simple solution to see whether it is broken. This is what to search for:
- Cracks or dents: These may point out that the magnetron has been broken by affect.
- Scorching or discoloration: This may be an indication that the magnetron has been overheating.
- Rust or corrosion: This may be an indication of water harm.
- Unfastened or broken connections: These may forestall the magnetron from working appropriately.
- Damaged or lacking insulation: This may expose the magnetron to moisture or electrical hazards.
Should you discover any of those issues throughout your visible inspection, it is best to exchange the magnetron.
Desk: Visible Inspection Guidelines
| Part | What to search for |
|---|---|
| Exterior | Cracks, dents, scorching, discoloration, rust, or corrosion |
| Connections | Unfastened or broken connections |
| Insulation | Damaged or lacking insulation |
Continuity Take a look at
The continuity check checks for an entire circuit within the magnetron. It does this by measuring {the electrical} resistance between two factors on the magnetron. If the resistance may be very low (near zero), then the circuit is full and the magnetron is functioning correctly. Nevertheless, if the resistance may be very excessive (near infinity), then the circuit is damaged and the magnetron will not be functioning correctly.
Step 1: Collect Your Supplies
You’ll need a multimeter and a microwave magnetron for this check.
Step 2: Set Up Your Multimeter
Set your multimeter to the continuity setting. That is often indicated by a logo that appears like a diode or a speaker.
Step 3: Disconnect the Magnetron
Unplug the microwave from the ability outlet. Take away the magnetron from the microwave.
Step 4: Determine the Magnetron Terminals
There are often two terminals on a magnetron. One terminal is related to {the electrical} provide and the opposite terminal is related to the microwave cavity. The terminals could also be labeled or they might be marked with completely different colours.
Step 5: Contact the Multimeter Probes to the Magnetron Terminals
Contact one multimeter probe to every of the magnetron terminals. If the multimeter beeps, then the circuit is full and the magnetron is functioning correctly. If the multimeter doesn’t beep, then the circuit is damaged and the magnetron will not be functioning correctly.
Step 6: Troubleshooting
If the continuity check fails, then you will have to troubleshoot the magnetron. Listed below are some doable causes of a failed continuity check:
| Attainable Trigger | Resolution |
|---|---|
| Damaged wire | Exchange the wire. |
| Unfastened connection | Tighten the connection. |
| Burned out magnetron | Exchange the magnetron. |
Resistance Take a look at
The resistance check is an easy solution to test if the magnetron is working correctly. To carry out the resistance check, you will have a multimeter. Set the multimeter to the ohms setting and join the results in the 2 terminals on the magnetron. The resistance needs to be between 0.5 and a couple of ohms. If the resistance is considerably greater or decrease than this, then the magnetron is probably going defective and needs to be changed.
Listed below are the steps on how one can carry out the resistance check:
1. Flip off the microwave and unplug it from the ability outlet.
2. Take away the outer cowl of the microwave.
3. Find the magnetron. It’s often a big, cylindrical part situated in the back of the oven.
4. Disconnect the wires from the terminals on the magnetron.
5. Set the multimeter to the ohms setting.
6. Join the leads of the multimeter to the 2 terminals on the magnetron.
7. Verify the resistance studying. The resistance needs to be between 0.5 and a couple of ohms.
8. If the resistance is considerably greater or decrease than this, then the magnetron is probably going defective and needs to be changed.
| Resistance Studying | Magnetron Standing |
|---|---|
| 0.5 – 2 ohms | Good |
| Beneath 0.5 ohms | Quick circuit |
| Above 2 ohms | Open circuit |
Voltage Take a look at
The voltage check is an important step in checking the microwave magnetron. It entails testing the voltage output from the magnetron to the wave information. The voltage needs to be between 3,000 and 4,000 volts. To carry out the voltage check, observe these steps:
-
Disconnect the ability to the microwave.
-
Take away the outer casing of the microwave.
-
Find the magnetron and the wave information.
-
Disconnect the wave information from the magnetron.
-
Join a voltmeter to the wave information.
-
Activate the ability to the microwave.
-
Observe the voltmeter studying.
-
If the voltage studying is between 3,000 and 4,000 volts, the magnetron is functioning correctly. If the voltage studying is under or above this vary, the magnetron is defective and must be changed.
Troubleshooting a Defective Magnetron
1. Verify for Seen Injury
Examine the magnetron for any indicators of bodily harm, reminiscent of burn marks or cracks. Should you discover any harm, the magnetron must be changed.
2. Take a look at the Continuity of the Filaments
Utilizing a multimeter, test the continuity of the 2 filaments within the magnetron. If both filament is damaged, the magnetron is not going to work correctly.
3. Take a look at the Diode
The diode within the magnetron prevents high-voltage electrical energy from flowing again into the transformer. Utilizing a multimeter, test the diode for continuity in each instructions. If the diode is defective, the magnetron is not going to work correctly.
4. Take a look at the Excessive-Voltage Transformer
Utilizing a high-voltage probe, test the output voltage of the transformer. The voltage needs to be between 2,000 and 4,000 volts. If the voltage is simply too low or too excessive, the transformer could also be defective.
5. Take a look at the Capacitor
The capacitor within the magnetron shops vitality and releases it to the diode and transformer. Utilizing a capacitor tester or a multimeter, test the capacitance of the capacitor. If the capacitance is simply too low or too excessive, the capacitor could also be defective.
6. Verify the Waveguide
The waveguide is a steel tube that carries the microwaves from the magnetron to the cooking chamber. Examine the waveguide for any harm or obstructions. If the waveguide is broken, the microwaves will be unable to achieve the cooking chamber.
7. Verify the Door Interlock Change
The door interlock swap prevents the microwave from working when the door is open. Utilizing a multimeter, test the continuity of the swap. If the swap is defective, the microwave is not going to function.
8. Reset the Microwave
Typically, a defective magnetron will be fastened by merely resetting the microwave. Unplug the microwave and watch for a couple of minutes. Plug the microwave again in and attempt to function it usually.
9. Exchange the Magnetron
If the entire above assessments have failed, the magnetron is probably going defective and must be changed. Changing a magnetron is a posh process that ought to solely be carried out by a professional technician.
Symptom Attainable Trigger Microwave doesn’t warmth meals Defective magnetron, defective diode, defective capacitor, defective waveguide, defective door interlock swap Microwave sparks or arcs Defective magnetron, defective waveguide Microwave makes a buzzing noise Defective transformer Indicators of a Defective Magnetron
In case your microwave will not be heating meals evenly or in any respect, it could possibly be an indication that the magnetron is defective. Different indicators of a defective magnetron embody:
- Arcing or sparking contained in the microwave
- A buzzing or buzzing noise
- The microwave door not closing correctly
Security Precautions
Earlier than you start working in your microwave, be sure you unplug it from the ability outlet. Additionally, put on security glasses and gloves to guard your self from any potential hazards.
Alternative
To interchange the magnetron, you will have to:
- Take away the outer casing of the microwave
- Find the magnetron and disconnect the wires
- Take away the mounting bolts and take out the magnetron
- Set up the brand new magnetron and reconnect the wires
- Exchange the mounting bolts and put again the outer casing
Reassembly
After getting changed the magnetron, you will have to reassemble the microwave. To do that, you will have to:
- Exchange the outer casing
- Join the ability twine
- Take a look at the microwave to verify it’s working correctly
Troubleshooting
In case you are having bother changing the magnetron, listed here are some troubleshooting suggestions:
- Guarantee that the ability is disconnected from the microwave
- Verify the connections between the magnetron and the wires
- Guarantee that the mounting bolts are tightened correctly
Further Ideas
Listed below are some extra suggestions for changing the magnetron in your microwave:
- Use a brand new magnetron that’s the identical kind and mannequin as the unique
- Comply with the directions rigorously and don’t skip any steps
- In case you are not snug changing the magnetron your self, contact a professional equipment restore technician
How To Verify Microwave Magnetron
The magnetron is an important part of a microwave oven, chargeable for producing the microwaves that warmth meals. A defective magnetron can result in poor heating efficiency and even full failure of the oven.
Checking the magnetron is a comparatively easy course of, utilizing a multimeter to measure resistance and continuity. Listed below are the steps to test a microwave magnetron:
- Unplug the microwave oven from the ability outlet.
- Find the magnetron, often located behind the cooking chamber.
- Disconnect the wires related to the magnetron.
- Set the multimeter to measure resistance (ohms). Join one probe to the terminal marked “anode” or “A” on the magnetron, and the opposite probe to the terminal marked “filament” or “F”. The resistance needs to be between 1 and 5 ohms.
- Change the multimeter to continuity mode. Join one probe to the terminal marked “anode” or “A” and the opposite probe to the steel physique of the magnetron. There needs to be no continuity, indicating that the magnetron will not be shorted to floor.
If the magnetron fails any of those assessments, it seemingly must be changed. It is essential to have a professional technician change the magnetron to make sure security and correct operation.
Folks Additionally Ask About How To Verify Microwave Magnetron
How do I do know if my microwave magnetron is working?
You possibly can test the magnetron utilizing a multimeter to measure resistance and continuity as described within the information above. If the magnetron is working correctly, it should present the right resistance and continuity readings.
What are the indicators of a foul microwave magnetron?
Indicators of a defective magnetron embody poor heating efficiency, uneven cooking, or full failure of the oven to warmth meals. Moreover, the magnetron might make a buzzing or buzzing noise throughout operation.
Is it harmful to exchange a microwave magnetron?
Changing a microwave magnetron will be harmful because of the excessive voltage concerned. It is important to have a professional technician carry out the substitute to make sure security and correct operation.
