The JBL Pulse is a well-liked Bluetooth speaker because of its portability, sound high quality, and built-in gentle present. Nonetheless, if it is advisable restore your Pulse or exchange a element, you will must know methods to disassemble it. Fortuitously, the method is comparatively easy and might be accomplished in only a few minutes with the best instruments.
To start out, you will want to collect just a few instruments. You may want a Phillips head screwdriver, a flathead screwdriver, and a spudger. You may additionally wish to put on gloves to guard your fingers from any sharp edges. After you have your instruments, you may start the disassembly course of.
First, take away the 4 Phillips head screws on the underside of the speaker. Then, use the flathead screwdriver to pry off the underside panel of the speaker. As soon as the underside panel is eliminated, you will see the battery, the circuit board, and the speaker drivers. To take away the battery, merely disconnect the battery connector and raise the battery out of the speaker. To take away the circuit board, disconnect the entire connectors and unscrew the 2 Phillips head screws that maintain the circuit board in place. To take away the speaker drivers, merely unscrew the 4 Phillips head screws that maintain every driver in place.
Methods to Disassemble a JBL Pulse
Disassembling a JBL Pulse is a comparatively easy course of that may be accomplished in about half-hour. The next steps will information you thru the method:
1.
Energy down the JBL Pulse and disconnect it from any energy sources.
2.
Take away the 4 screws on the underside of the JBL Pulse. These screws are situated in every nook of the system.
3.
Gently pry open the again cowl of the JBL Pulse. The again cowl is held in place by a sequence of clips. Watch out to not harm the clips.
4.
Find the battery and disconnect it from the motherboard. The battery is situated within the middle of the system. It’s held in place by a single screw.
5.
Take away the 4 screws that safe the motherboard to the chassis. The motherboard is situated within the high of the system.
6.
Gently raise the motherboard out of the chassis. Watch out to not harm the ribbon cables that join the motherboard to the opposite elements.
7.
Disconnect the ribbon cables that join the motherboard to the opposite elements. The ribbon cables are situated on the perimeters of the motherboard.
8.
Take away the remaining elements from the chassis. The remaining elements embody the speaker, the LEDs, and the buttons.
After you have disassembled the JBL Pulse, you may start to restore or exchange the broken elements.
Individuals Additionally Ask
How do I repair a JBL Pulse that will not activate?
There are some things that might trigger a JBL Pulse to not activate. First, guarantee that the battery is charged. If the battery will not be charged, attempt charging it for not less than half-hour. If the battery is charged, however the JBL Pulse nonetheless will not activate, attempt resetting the system. To reset the system, press and maintain the facility button for 10 seconds. If the JBL Pulse nonetheless will not activate, it’s possible you’ll must contact customer support.
How do I exchange the battery in a JBL Pulse?
To interchange the battery in a JBL Pulse, you have to to disassemble the system. After you have disassembled the system, you have to to find the battery. The battery is situated within the middle of the system. It’s held in place by a single screw. After you have situated the battery, disconnect it from the motherboard and take away it from the system. To put in the brand new battery, merely reverse the steps.
How do I restore the LEDs in a JBL Pulse?
To restore the LEDs in a JBL Pulse, you have to to disassemble the system. After you have disassembled the system, you have to to find the LEDs. The LEDs are situated on the perimeters of the motherboard. After you have situated the LEDs, you have to to check them to see which of them are usually not working. To check the LEDs, you have to a multimeter. After you have recognized the defective LEDs, you have to to switch them. To interchange the LEDs, you have to to desolder the previous LEDs and solder within the new LEDs.
